Skip to content
Henan mine crane co., ltd. Get a project quote
STEEL MILL CRANES

360 t Casting Crane for Steel Production

A 360 t ladle lift places high demands on bridge alignment, drive control and availability during steel production.

ApplicationLuzhou Xinyang casting-crane installation
Installed equipmentProject-specific lifting arrangement
Site-specificLoad, route, duty and delivery scope
Casting overhead crane installed in a steel production workshop
Casting overhead crane installed in a steel production workshop.
THE OPERATING CHALLENGE

Start with the load and the process route.

A 360 t ladle lift places high demands on bridge alignment, drive control and availability during steel production.

The crane, lifting attachment, building interface and control sequence need to be reviewed as one operating system.

Prepare the technical brief ↗
01 / DEFINE

Filled ladle and beam mass

02 / DEFINE

Span and route drawings

03 / DEFINE

Production duty and downtime target

04 / DEFINE

Drive, monitoring and redundancy scope

ENGINEERED FOR THE APPLICATION

Make high-capacity ladle travel smooth and inspectable.

Use a casting-crane arrangement designed around the filled ladle, production route and runway. Coordinate bridge fabrication accuracy, controlled acceleration, fault diagnosis and redundant mechanisms so the lifting sequence can be operated and maintained reliably.

Casting overhead crane installed in a steel production workshop
Casting overhead crane installed in a steel production workshop.
01

Confirm full lift mass

Include the filled ladle and all lifting gear in the capacity basis.

02

Control the route

Plan slow-speed positioning near the furnace and pouring stations.

03

Inspect each cycle

Use monitoring and diagnostic information to support maintenance decisions.

✓

Drive and brake behavior

Specify controlled starts, stops and holding at the heaviest load.

✓

Redundancy and service access

Define which mechanisms need backup and how maintenance will be performed.

PROJECT IN OPERATION

Luzhou Xinyang casting-crane installation

The project used a 360 t casting crane in service at a steel plant with 2 million-ton production capacity, using controlled drives, fault diagnosis and redundant mechanisms.

Process fit360 t Casting Crane for Steel Production Solution
EquipmentFour-Girder Casting Crane / Double-Girder Casting Crane
ProjectLuzhou Xinyang casting-crane installation
Technical reviewCustomer load and site drawings
SPECIFICATION FOR YOUR SITE

Define the operating brief before fixing a crane model.

Project figures above describe a delivered application. Your crane rating, dimensions, controls and documentation follow the approved site brief.

InputInformation needed for this applicationConfirm in the technical offer
01 / Load and attachmentFilled ladle and beam massRated load including the attachment, lifting-point arrangement and load cases.
02 / Plant geometrySpan and route drawingsCrane span, lifting height, headroom, wheel loads and runway or foundation interfaces.
03 / Operating dutyProduction duty and downtime targetDuty classification, speeds and control behaviour matched to the agreed operating cycle.
04 / Environment and controlsDrive, monitoring and redundancy scopeProtection, positioning, interlocks, monitoring and safe recovery requirements.
Destination and deliveryCountry, project standards, quantity, freight and site services.Documents, inspection and testing, packing, installation support and agreed delivery milestones.
Have a preliminary layout?

Send the available load schedule and drawings. The missing inputs can be identified during technical review.

Discuss your project ↗
FROM OFFER TO HANDOVER

Compare the complete lifting package.

The offer should state the equipment boundary, documents, inspections and site responsibilities for your destination.

01

Engineering

General arrangement, load basis, runway and utility interfaces, control and protection schedule.

02

Manufacture & inspection

Approved drawings, inspection plan and factory testing for the selected configuration.

03

Shipping & site work

Packing, freight, erection support, commissioning and operator training as specified.

04

Handover

Test records, manuals, maintenance instructions and agreed spare-parts list.

Order quantity, compliance and delivery schedule

Single-crane and multi-crane packages are available. Your quotation defines the destination standards, required certificates and inspection records, packing, site services and production schedule after drawing approval.

RELATED CRANES AND SOLUTIONS

Compare equipment for this operating task.

These product families and related applications provide a starting point. Final selection follows the load and site review.

BUYER QUESTIONS

Before you request a quotation.

What information is needed to specify this crane solution?

Send the full load and lifting-gear mass, route or bay drawing, operating cycles, working environment, controls and destination requirements.

Can the crane be customized for our plant?

Yes. The equipment arrangement, attachment and controls are selected for the approved load, route, runway and process conditions.

What are the order quantity, certification and lead time?

We can quote a single crane or a coordinated fleet. The project offer states the agreed destination standards, inspection and test documents, manufacturing schedule after drawing approval, and shipping or site-service scope.

LET'S REVIEW YOUR PROJECT

Send the 360 t casting crane for steel production brief. Get a crane proposal built around your process.

Share your load, layout, work cycle and destination. Our team can review the crane, lifting attachment and delivery scope together.

Send your project requirements ↗